All Rooms

Did you know that up to 70% of the heat from the back of a radiator is used to heat the wall behind it. Only about 30% is used to heat the room itself.
As the radiator warms up, it warms the wall behind it. The heat is then transferred to the outside of the wall where it is lost.
Energy is saved and the fuel bills are substantially reduced giving very early payback periods (6 months to 24 months).
These panels have Ofgem accreditation for EEC schemes and after fitting your radiator panels they will reduce your heating bills by up to 20%. That's £60 a year for the average 3 bedroom semi-detached house, which means they will pay for themselves in as little as one season.

The Novitherm Panel is a unique profiled thermal insulator, the result of years of intensive research.

Without Novitherm the radiator must first heat up the wall behind - this heat seeps through the wall and out of the building.

There is no need to remove the radiators to fit the panels and they come complete with comprehensive fitting instructions and a roll of double-sided tape.

Each panel is 688mm high x 444mm wide. Generally each standard sized radiator will need two panels.

With Novitherm the hot air natually rising behind a radiator is caused to spin by the profile of the panel creating a series of vortices, rising at higher speed, and continuing to spin out into the room. The wall behind the panel stays cool.

The rising air curtain extending 2-3 meters above the radiator prevents heat dissipation through the wall and any window above.
The comfort level in the room is significantly improved.
Deteriation behind the radiators and discolouration above is reduced.
The enhanced convective flow pattern improves heat distribution, reduces heat up time and virtually eliminates cold spots. Manufactured in the UK. Registered at UK Patent Office Reg. No. 1012561
The Novitherm panel fits behind the radiator and reduces the wasted heat by insulating the wall keeping it virtually cold. The heat that is saved either heats the air in the room, warming it faster, or is retained in the system so the boiler fires less and uses less fuel.

Helps to reduce carbon dioxide emissions
Reduces heating costs by at least 15% and pays for itself within 2 heating seasons
Increases return water temperature allowing the boiler to fire less often and for shorter periods
Increases and improves convection behind the radiator eliminating cold spots and improving heat distribution
Prevents primary heat loss through the wall
Simple to install without the need to remove the radiator and are not visible
It is unaffected by moisture or water ingress
It can be removed and re-laid without reducing efficiency

Key:
A Wall with radiator
B Full length window
C Wall without radiator
D Wall with radiator insulation panel
In a test conducted at Nottingham City Hospital using Thermal Imaging cameras from outside the building show just how effective our Radiator Insulation Panels are.
Comparison of A and D shows extremely efficient performance of panel, reducing heat loss through the wall.

After panel fitment the increased air acceleration and redirection of the airflow pattern, achieves a more even distribution of heat, which raises comfort levels for all the occupants: this benefit is felt immediately. Saw Tooth Rad-Panels particularly effective when used with LST radiators.

Thermilate® is an insulating paint additive for house paint. It is used for both interior paint and paints for exterior use. Thermilate® turns a painted surface, such as walls and ceilings in your home, into a thermal paint barrier

It can save you up to 25% on your heating bills and make 40% savings in cooling requirements! Saves Energy! , Saves Money!

Insulating Paint additive: Add to House Paint

Thermilate® insulate paint additives are formulated for mixing into to your locally available house paints enabling those house paints to achieve a very high insulation value which SAVES YOU MONEY ON YOUR HEATING AND COOLING BILLS!

Thermilate® INSULATING PAINT pre-mixed and ready to use house paint for your residential and commercial paint applications can greatly reduce your utility bills and create a more comfortable home with the convenience of a ready to use formula!

Thermilate®

" Winter or summer
" Interior or exterior.

Thermilate is the powder that makes paint insulate! The microspheres within the powder act as mini thermos flasks. Thermilate powder is mixed with ordinary paint (one pack mixes into 5 litres of paint) to make an insulating coating that can keep heat in or out. Ideal for insulating buildings, rooms, water tanks, hot or cold water pipes.

Saves up to 25% energy with original NASA technology
Bonds well to a range of surfaces
Resistant to atmospheric pollution
Stable over a wide range of temperature variations
Remains intact on flexible surfaces
Excellent hiding and gloss retention
Exceptional film durability
Mildew resistant
Easy to apply
Rapid drying for quick re-coating
Easy cleanup with soap and water
Adds a high insulating value to all house paints.
Safe, non-toxic & environmentally friendly.
Works with house paint on roofs, walls and ceilings
Greatly reduces heating and cooling costs.
Simply mix into your paint and apply as usual.

Pack size: 500g

Scalewatcher is a compact, computerised electronic water conditioner which will descale your existing system, prevent new scale forming and save you money from the moment it is installed.

Scalewatcher could be saving you up to £190 IN JUST ONE YEAR

If you are in one of the 60% of households in the UK living in a hard water area, it could be costing you up to an extra £190 in energy and maintenance, according to official published figures.

By descaling your system and preventing new lime scale formation, Scalewatcher starts to save you money from the moment it's installed.

We guarantee that the Scalewatcher will work for you or we will refund your money.

Hard Water Costs Hard Cash

Tested or reported on by Which! Perfect Homes, Home Building and Decorating, Build It, Practical Householder, Kitchens Bedrooms and Bathrooms, Essential Living and Garden Answers. No other product has this test record and some have no consumer tests.

Audio or radio frequency - Scalewatcher uses a patented audio frequency system. Most other products therefore use radio frequency. This is not as effective and needs more space for two coils and can interfere with radio and TV.
Success rate - Scalewatcher has a proven 98% success rate.
Designed to Last - Scalewatcher is built of the highest quality components and has a computerised circuit board protected by resin encapsulation with an estimated life of twenty years. Most others have no protection and therefore are prone to corrosion, with an expected life of around five to ten years.

Transformer - Scalewatcher has a built in transformer - others often use external transformers built into plugs. These have a limited life, usually five years, are difficult to replace and can run hot.
External Box - Scalewatcher is boxed in a high quality box designed for a twenty year life. Others are usually a very thin plastic with a life of around five to ten years.
Technical Support - We offer a free technical visit if required in addition to our telephone help line.

No other product on the market has all the features of the Scalewatcher, which adds up to the best performing, longest lasting water conditioner available and with excellent after sales back up.

The EPS Power Saver uses state of the art electrical technology to actively monitor and improve the power factor of your household appliances. In addition, the intelligent technology optimises the voltage and current demands thus reducing the active power / KWh demands and achieves around 10% to 20% savings on your electricity bill.
Choosing the model:
EPS188:Suitable for use in any premises where the monthly electricity usage is between 300 KWh - 1000 KWh per month.
EPS388: Suitable for use in any premises where the monthly electricity usage is between 1000 KWh - 2500 KWh per month

It also acts as a voltage stabilizer by storing energy for up to 10 seconds and therefore supplies load with proper voltage during momentary power surges.
10-20% Reduction on your electricity bill

10% - 20% reduction in your electricity bill.
Plugs into any socket. No re-wiring needed.
Suitable for homes, shops, restaurants and offices.
No maintenance required.
Rapid return on your investment.
Two Year 1-1 exchange warranty.
Fully compliant with safety standards.
Environmentally friendly.
Weight: 500 gm
Size:126 x138 x 80 mm (5 x 5.5 x 3")
Not available for US and Canada customers

The EPS Power Saver uses state of the art electrical technology to actively monitor and improve the power factor of your household appliances. In addition, the intelligent technology optimises the voltage and current demands thus reducing the active power / KWh demands and achieves around 10% to 20% savings on your electricity bill.

It also acts as a voltage stabilizer by storing energy for up to 10 seconds and therefore supplies load with proper voltage during momentary power surges.

Installation of the Power Saver could not be easier. Just plug the unit into any 13 Amp socket on your premises and that’s all you need to do.
For a safe and reliable operation, EPS recommends that the unit should be plugged into a wall socket and not an extension lead. The device can store energy for up to 10 seconds after it is switched off, therefore wait for at least 10 seconds between switching off the mains and un-plugging the device.

Specifications: Weight:500 gm Size:126X138X80 mm (5x5.5x3 inches)

The EPS Power Saver unit offers a minimum of 10% reduction in your electricity bill from day 1, therefore saving you money. The amount of reduction depends upon the type of load and the usage pattern. On average our customers have genuinely seen the following savings.

10% - 15% savings in residential premises.
15% - 20% savings in business and commercial premises.

The EPS Power saver unit can be returned within 2 months of purchase, if our product does not deliver the savings we promise. A proof of purchase is required.

The money back guarantee is invalid if:
· The returned Power Saver has visible damage caused by misuse, neglect or tampering with the unit.
· The serial number has been removed from the Power Saver.
Warranty
The Power Saver unit comes with a 24-month 'new for old' warranty, covering any manufacturing or material defects.

Will the Power Saver unit definitely reduce my electricity bill
EPS offer a unique money back guarantee, which proves to our customers how confident we are about our product.

The Power Saver unit will definitely reduce your electricity bill. Based on customer feedback and extensive tests, savings between 10 – 20% have been recorded under normal conditions. The %age savings will depend upon the type of load and the consumption. In some cases, savings above 20% have been recorded, especially in shops and offices.

Does the Power Saver require any maintenance?
No. Simply plug the Power Saver unit on your premises and start saving money.

Do I need to make any changes to the electrical wiring?
No. The Power Saver is designed as a Plug & Play device. Simply plug the unit into a13 Amp socket on your premises. EPS recommends that the power saver should be plugged into a wall socket, not an extension lead.

Which Power Saver model is suitable for my use?
The Power Saver unit has two models. The EPS 188 model is suitable for residential use, for up to a 4 bedroom home. The EPS 388 is suitable for larger homes, schools, offices, schools, shops and restaurants.

Is the Power Saver unit suitable for use in a 3 phase systems?
Yes. The EPS 388 model is suitable for use in a 3-phase system. However, for a 3-phase system, only our qualified electricians can carry out the installation of the EPS 388 Power Saver unit. Please contact our customer services team, who will be happy to assist you with your requirements. Please note that EPS 388 is not suitable for heavy-duty industrial load or monthly consumption exceeding 6000 KWH.

How long will it take to recover the cost of buying a Power Saver unit?
Based on customer feedback and field-testing, the original investment on the Power Saver can easily be recovered in 4 - 6 months, therefore allowing you to enjoy additional savings for years to come.

Is the Power Saver unit safe?
Yes. The Power saver unit is built to the highest possible manufacturing standards.

Q12: Do I leave the Power Saver Unit ‘switched-on’ continuously?

Ans: Yes. The Power Saver unit should be left 'Switched ON' continuously to achieve the maximum savings. EPS recommend that the unit should be switched off during long periods of inactivity, for example, when going abroad on holiday, or if the premises are closed for long periods of time.

Please note that the Power Saver unit can store energy for up to 10 seconds after it is switched off, therefore wait for at least 10 seconds between switching off the mains and un-plugging or relocating the device.



Q13: Can the Power Saver unit be wall mounted?

Ans: Yes. The user manual has detailed instructions for the wall mounting preparation.



Q14: Is the Power Saver environmentally friendly?
Yes. Power Saver helps improve the environment by minimising the amount of reactive power which otherwise is wasted in distribution networks, cables and your appliances in the form of heat.

The simple, cost-effective way to stop chimney draughts, reduce noise and heat loss.

Special laminate of three poly plastics make it airtight, tear-resistant and long-lasting.
Shape allows some ventilation on two corners to keep the chimney dry.
Completely safe: if it is accidentally heated, it shrivels and deflates.

Inflate your chimney balloon by mouth inflation tube or air bed pump. Before lighting a fire deflate it by opening the tap and then remove it. Use it again and again.

Stops chimney draughts
Can be fitted by anyone in a couple of minutes
Stops debris, soot and bird mess
Reduces outside noise entering the room
Saves on heating bill by stopping downdraughts and updraughts
Allows a little ventilation
Sizes to fit all chimneys
Inflate to install, deflate to remove. Use again and again
The Chimney Balloon has been saving families energy and money for more than 15 years.

All sizes shown are chimney sizes and not balloon sizes. The balloon itself will be slightly larger.

Small size - Typical modern fireplace
Medium size - Victorian fireplace (Most popular size)
Large size - Georgian fireplace
The sizes are length x width.

How to choose the correct size Chimney Balloon.

Before sizing your chimney make sure your fireplace and chimney are cold with no hot ash in the fireplace. Sweeping and vacuuming your fireplace will help make it easier. If you chimney has a damper you should see a metal flap with a lever that closes the chimney.

Chimneys with a damper

The Chimney Balloon should be installed, generally above the damper. Select an area for its installation making sure that this does not interfere with the damper flap or any damper hardware. The area must have parallel or slightly sloping walls ideally with texture for the balloon to grab and lodge when inflated. The damper ledge acts to provide extra support to the weight of the balloon. A Chimney Balloon can also be installed well above the damper, so it is possible to close the damper below it.

Measure the length and depth of the chimney in the location you have selected to install the balloon. Write down the dimensions, and also note if your chimney is round, circular or rectangular in the location you are measuring.

Chimneys without a damper (a chimney with no closing mechanism)

Identify the narrowest part of your chimney within arms reach. Choose an area to install the Chimney Balloon. Make sure the area you select is not interfered with by any hardware or sharp edges in the chimney. The area must have parallel or slightly sloping walls ideally with texture for the balloon to grab and lodge when inflated.

Measure the length and depth of the chimney in the location you have selected to install the Balloon. Write down the dimensions. Measure your chimney about 30cm or so up out of sight where your Chimney Balloon will fit as shown in the diagrams. You will need the side-to-side and the front-to-back inside dimensions. We suggest you use a flexible steel tape measure (Stanley type) or two pieces of cardboard extended like wings.

It is only necessary to measure approximately and choose the Chimney Balloon of the approximate size or slightly bigger than your chimney.

How do I choose the correct size Chimney Balloon if there is a smoke shelf or smoke chamber in my chimney?

Sizing Tips

On any measured flue opening smaller than 12"X12" you should order a Chimney Balloon the exact size or no more than 3" too large in length or width.

On any measured flue opening larger than 12"X12" you should order a Chimney Balloon the exact size or no more than 6" too large in length or width.